Dehumidifier Not Collecting Water? What to Check, in Order
Start with the room before you suspect a part. A unit stops pulling water once the room reaches the humidity you set, and it pulls little or nothing once the air drops below its rated minimum, which is 41°F for the Midea Cube and the Frigidaire 35-pint.
Put a hygrometer next to the unit and compare it with the setting. A room at or below the setting, or a few points above it, means the unit is doing its job. If it reads well above, check the air temperature against the unit’s rated minimum, then make sure the bucket is seated and no drain hose is carrying the water away, then look at the filter. A coil that stays iced means the air is too cold or isn’t moving. An error code points to a repair. So does outlet air that feels no warmer than the room when the unit isn’t defrosting.
| Cause | How to tell | What to do |
|---|---|---|
| 1. Room already at the setting | A hygrometer by the unit reads at, below or within a few points of the setting; the HD55S power light blinks | Nothing, if the gauge reads 50 or less; otherwise set the unit a few points lower (see the humidity targets) |
| 2. Air below the rated minimum | Under 41°F for the Midea Cube or Frigidaire 35-pint, under 38°F for the Hisense; the HD55S shows LO under 33.8°F | Warm the space, or switch to a unit rated colder (below 38°F, only the AlorAir): Hisense 35-pint, budget tier on Amazon; AlorAir HD55S, mid-range tier on Amazon |
| 3. Bucket full, unseated or bypassed | The Cube shows P2 (full) or Eb (bucket out of place); a hose on the drain port sends water past the bucket | Empty and reseat the bucket; with a hose on the port, follow it to its end |
| 4. Coils iced over | Frost that stays on the coil instead of clearing | Switch off until it thaws, then fix the cause (step 2 or 5) |
| 5. Filter clogged or airflow blocked | Weak airflow; the Cube’s filter light comes on after 250 hours of running | Wash the filter; give the unit clear space on every side |
| 6. A failed part | Fan runs but the outlet air is no warmer than the room; Midea EH codes, AlorAir E3 or E5 | Midea codes: unplug and restart once, then call for service. AlorAir E3 or E5: call for service |
1. The room is already dry
A dehumidifier with a humidistat runs its compressor until the air reaches the setting, then stops pulling water. The HD55S blinks its power light when it gets there. Midea’s troubleshooting table lists reaching its preset level as a reason the Cube won’t start.
Built-in readings drift, though. AlorAir rates its own display at plus or minus 5 percent, so a unit set to 50 can sit idle while a separate gauge reads 54. Put a hygrometer that you’ve checked against damp salt beside the unit (the basement humidity level page has the method) and compare the two. A gauge at or under the setting means nothing is wrong. If it reads higher and the unit sits idle, I’d set the unit a few points lower and check again the next day. The HD55S won’t go below 35 on its humidistat; any lower setting switches it to continuous mode.
ENERGY STAR suggests 30 to 40 percent indoors during the heating season in colder climates. A gauge in that range in January, next to an idle unit set to 50, means the unit is working.
2. The air is colder than the unit is rated for
Midea rates the Cube for 41°F to 95°F and warns that its coils can frost over in colder air. The HD55S runs down to 33.8°F; below that it shows LO on the display and won’t start at all.
| Model | Rated minimum | Source |
|---|---|---|
| Santa Fe Classic | 56°F | Santa Fe spec sheet |
| AprilAire E100 | 50°F | AprilAire spec sheet |
| Frigidaire 35-pint | 41°F | Frigidaire product page |
| Midea Cube 50-pint | 41°F | Midea owner’s manual |
| Hisense 35-pint | 38°F | Hisense product page |
| AlorAir HD55S | 33.8°F | AlorAir owner’s manual |
Above the floor, output still falls as the air cools. Household units are rated at 65°F under the Department of Energy’s test, and ENERGY STAR notes that frost can form on the coils below 65°F. A Midea Cube in a 45°F basement is inside its rating and still pulling less than its 50 pints a day.
Set a thermometer on the floor next to the unit and read it on the coldest morning of the week. Under 41°F, the Frigidaire and the Midea are past their rating; the cold-basement guide picks the Hisense from 38 up to 41°F and the AlorAir HD55S below that, down to its 33.8°F floor. None of them is rated for freezing air. A Santa Fe Classic, rated to 56°F, is already below its floor in a basement in the low 50s.
3. The water is going somewhere else
Check the bucket next. ENERGY STAR notes that most units shut off on their own when the bucket fills. The Cube shows P2 when its bucket is full and Eb when the bucket isn’t seated, and it stays stopped until the bucket is back in place. Bucketless mode is only for a Cube with a hose on its drain port; without a hose, the bucket has to be seated after every emptying and washing or the unit won’t run.
An empty bucket with a hose attached may mean the unit is working fine. With the drain cap off and a hose on the port, the Cube’s continuous drain sends water down the hose to a floor drain, and Midea says the unit has to sit above that drain for the water to flow. Follow the hose and look for water at the far end. A hose that sags or climbs partway along holds water back; AlorAir’s install steps ask for a drain line that falls at least 1 inch every 10 feet, with no low spots or loops.
The same Midea manual covers the Cube with a built-in pump. On that model, a blinking pump light means the pump can’t move water. Midea’s fix is to rinse the pump filter, clear the hose and empty the bucket, and it asks for the bucket to be emptied at least once a week in pump mode. Don’t run a drain or pump hose outdoors at 32°F or colder; Midea warns that ice in the hose blocks it and stops the unit. For a basement with no floor drain at all, the pump guide compares the two pump models.
4. Ice on the coils
Midea’s table calls frost on the coils normal because the Cube defrosts itself, and the HD55S turns its auto-defrost light red while it clears the coil. A unit isn’t collecting water while it defrosts, so in a cool room the bucket fills slowly.
For ice that builds into a solid layer and doesn’t clear, ENERGY STAR’s advice is to switch the unit off and let it thaw before turning it back on. When the ice comes back, either the room is too cold for that unit, which sends you back to step 2, or air isn’t reaching the coil, which is step 5.
5. A clogged filter or blocked airflow
A dehumidifier pulls water only from the air that crosses its coil, so anything that slows the airflow slows the bucket. The Cube’s filter light comes on after 250 hours of running, a little over ten days around the clock; the filters pull out from each side and rinse in clean water, and Midea says not to run the unit without them. AlorAir’s table for the HD55S lists a clogged filter as the cause of low airflow and calls for a foaming coil cleaner once a year.
Midea asks for 8 inches of clear space on every side of the Cube and 16 inches in front of the outlet. ENERGY STAR says to keep a unit away from walls and furniture, and away from dusty work such as a woodworking bench, since dust clogs coils and grills. Both also ask for the doors and windows to the space to stay closed while it runs.
6. A part has failed
Give the unit time before you test this. Midea builds in a 3-minute delay before the compressor restarts, and asks for a continuous 24-hour run when the Cube is new. Then, with the room above the setting, no defrost under way and, on the HD55S, the compressor light green, hold a hand at the outlet; AlorAir’s listing says the HD55S pauses its compressor while it defrosts, so a cool outlet during defrost proves nothing. AlorAir’s manual describes the air being reheated across the condenser on its way back into the room, so a running compressor sends out air warmer than the air going in. Air no warmer than the room with the fan running means the compressor isn’t running. No airflow at all points to the fan.
On the Cube, EH60 and EH61 are temperature sensor faults and EH0b is a fault between the display and control boards; Midea’s instruction for all three is to unplug the unit, plug it back in and call for service if the code returns. For the HD55S, AlorAir’s table says to contact your installer for E3 (abnormal coil temperature) and E5 (refrigerant leak); for a unit you set up yourself, that means AlorAir. Its compressor light shows red while it warms up and green once it’s running.
Compressor and refrigerant faults go to warranty service. The Frigidaire 35-pint carries 1 year of parts and labor, the Midea Cube 1 year (Midea lists no further terms), and the Hisense 2 years of parts and labor. AlorAir’s 6-year limited warranty on the HD55S covers parts, labor and replacement for the first 2 years and refrigeration parts for years 3 to 6, for orders placed on or after May 14, 2026. Warranty terms for 13 units are compared on the most durable dehumidifier page.
Collecting water, but the humidity stays high
A unit that fills its bucket every day while the gauge stays above the setting for days at a time is outmatched by the space. The sizing guide reads the pints you need off ENERGY STAR’s table by area and dampness, and a 35-pint unit falls short of the 40 pints at the top of the very damp row. A reading that jumps after every rain means water is coming in from outside; the wet basement guide starts there.
Why is my dehumidifier running but not collecting water?
If a hygrometer reads above the setting, look first at the air temperature, since below the rated minimum the fan can keep running while the coil frosts (the HD55S shows LO and stops instead), and then at any hose or pump carrying the water off before it reaches the bucket.
How long should a new dehumidifier run before it collects water?
Midea asks for a 24-hour continuous run on a new Cube. A bucket still dry after that, with a hygrometer reading above the setting and the air above the unit’s rated minimum, sends you to step 3.
Does continuous mode make it collect more water?
Only while the room is above the level the unit would otherwise stop at. Any HD55S setting under 35 percent switches it to continuous mode, which runs it regardless of humidity; in a dry room that adds hours of running and very little water.
A hygrometer and a thermometer first
I’d put both beside the unit before unplugging anything; between them they settle steps 1 and 2. If the room runs below the unit’s floor, warm it or replace the unit with one rated colder: the Hisense 35-pint below 41°F down to 38°F, for a moderately damp space, or the AlorAir HD55S below 38°F down to 33.8°F.
Troubleshooting steps come from the Midea MAD50S1QWT-A user manual (midea.com, file revised March 2026), the AlorAir Sentinel HD55/HD55S Installation and Operations Manual (alorair.com, August 2024) and ENERGY STAR’s dehumidifier page; the HD55S defrost pause from AlorAir’s Amazon listing; rated minimums from Frigidaire, Hisense, and the Santa Fe and AprilAire spec sheets; warranty terms from each maker. All checked November 2026. This page contains affiliate links. If you purchase through these links, Dehumidifier Advisor may earn a commission at no additional cost to you. See our affiliate disclosure for details.